The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
This article which follows in relation to How to Install a Bathtub is exceedingly remarkable. You should check it out.
Installing a bath tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately tough task. If the old bathtub is easily accessible, the project can relocate rapidly; if you need to open a wall to get rid of the old tub as well as position the brand-new bathtub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. See to it you have certified yourself for the task and are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to consider utilizing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will assist you install a new bath tub in your bathroom if you have already bought a brand-new tub as well as don't need to alter the arrangement of your previous water supply pipelines.
Your tools and also product checklist must comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be rather problematic due to the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will come from the pipes. Once the supply pipes have been eliminated, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin making sure that the washers remain in location in between the tap and the sink. Secure the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wooden boards under its feet, put the bath tub in the required position. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bathtub till the level reviews level.
To set up taps, fit the bottom of the furthest flexible faucet connector to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water system and also inspect all joints and new pipework for leakages and also tighten them if required. Fill up the bathtub as well as also check the overflow outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bath paneling as explained in the producer's user's manual. Tiling and securing around the bath tub ought to wait till the bathtub has actually been made use of a minimum of once as this will certainly settle it into its final placement.
Getting ready for the Installation
First of all, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to avoid strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its last setting.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to crack an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, causing difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the motion experienced when the tub is in usage. The sealer can split rather early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that write-up on How to Install a Bathtub through an associate on our other domain. Liked our write up? Please share it. Help others check it out. Thanks so much for going through it.
Visit Page Report this page